Effective November 22, 2026

Suppliers & Tier-1sEngineering notice

GM Bolt Console Bracket Cuts Piece Cost 83%, Wins SPE Award

GM's 2027 Bolt and Hummer EV won SPE awards for lightweighting: a US Farathane console bracket cutting cost 83 percent and a Hanwha GMT frunk cutting mass 34.2 percent.

Scope of change

  1. 2027 Chevrolet Bolt console bracket by US Farathane cut piece cost 83 percent and weight 45.8 percent (520.5 to 282 grams), winning SPE's Body Interior award.
  2. The bracket uses 25 percent glass-reinforced, 15 percent mineral-filled polypropylene with 60 percent recycled content and meets a 900-Newton abuse load.
  3. 2027 GMC Hummer EV frunk by Hanwha Advanced Materials swapped 1.8-density SMC for 1.2-density GMT, cutting mass 34.2 percent and cost 33.75 percent.
  4. The GMT frunk carries a 75-kilogram knee load with no more than 10 millimeters deflection and reached 100 percent PPAP in one month.
  5. Both vehicles were honored at SPE's 55th annual Automotive Innovation Awards competition, themed "Plastics: The Road to Innovation."
GM EVs Cited for Lightweighting Innovation
Fig.GM EVs Cited for Lightweighting Innovation — Quanlecntt2004 / pixabay

An 83 percent piece-cost reduction carried the 2027 Chevrolet Bolt to a Body Interior award at the Society of Plastics Engineers' 2026 Automotive Innovation Awards, the 55th edition of the competition. The winning part is a structural console bracket, injection molded by US Farathane Corp. in Troy, Michigan's supplier base, that replaces a three-piece welded steel assembly.

The bracket serves as the structural bridge between the front and rear sections of a two-piece floor console. It ties both sections to the lower body structure and controls cross-car sway, cupholder shake and rattle. GM's engineering requirement was a 900-Newton abuse load, and the part meets it.

What changed in the material?

The resin is a 25 percent glass fiber-reinforced, 15 percent mineral-filled polypropylene homopolymer with 60 percent recycled content. Optimized rib architecture in that material raised console modal frequency from 26.5 to 27.37 hertz — a small delta on paper, but enough to move the assembly out of a rattle-prone range.

The claimed numbers stack up as follows:

  • Piece cost down 83 percent.
  • Weight down 45.8 percent, from 520.5 to 282 grams.
  • Tooling lead time cut from 36 to 12 weeks.
  • Multipoint welding eliminated, which SPE says improved quality.

Award submissions are supplier- and OEM-authored claims, not audited production data. Still, the scale of the cost gap between a single molded part and a welded steel assembly is consistent with known tooling economics. What the citation does not say is annual volume, program timing beyond the 2027 model year, or whether the bracket has passed full production validation.

What did the Hummer EV frunk deliver?

The 2027 GMC Hummer EV took the Electric and Autonomous Vehicle Systems award for a front trunk supplied by Hanwha Advanced Materials. The redesign swaps 1.8-density structural sheet molding compound for 1.2-density glass mat thermoplastic. A 30 percent glass GMT forms the body of the part.

Robotically placed 45 percent unidirectional glass GMT locally reinforces the floor. The target is a 75-kilogram knee load carried with minimal body support and no more than 10 millimeters of deflection. One-shot compression molding delivers a Class A surface without carpet covering.

Hanwha replaced pumpable adhesives with ultrasonic welding, which enables end-of-life recycling — a claim worth watching, since GMT recyclability depends heavily on local reprocessing infrastructure. Fiber length, orientation and placement were controlled to hold structural performance without compromising dimensional stability, the citation says.

The measured outcomes: mass fell 34.2 percent, cost fell 33.75 percent, and the part reached 100 percent PPAP — production part approval process — in one month. A one-month PPAP is fast for a structural frunk. That figure is the supplier's own submission.

What to watch next

The Bolt launches for the 2027 model year, and that timing is the first real checkpoint: watch whether the Farathane bracket reaches series production at the claimed weight and cost, or whether steel returns quietly. The second marker is adoption. GMT with unidirectional local reinforcement is not yet common in high-volume EV enclosures; if other OEMs follow Hanwha's one-shot compression molding route, the 1.2-density frunk becomes a template rather than an outlier. SPE's competition theme, "Plastics: The Road to Innovation," signals where the materials lobby wants the industry to look.

via bnpmedia.com (Original)

Filed under

  • chevrolet-bolt
  • gmc-hummer-ev
  • automotive-plastics
  • injection-molding
  • supplier-innovation
Share this article:

More from Amara Osei

Amara Osei

Show full bio

Market editor covering technology and product news in Automotive manufacturing and vehicle production at Autoplant Brief.

342 articles

Also circulated

« Previous article